EternaBond DoubleStick
MicroSealant Putty Tape Go Back
DoubleStick is pure EternaBond advanced MicroSealant with a removable siliconized release liner on each side. Designed to bond two surfaces, even two surfaces made of two or more dissimilar materials. Double- Stick creates a tight, permanent, waterproof seal. DoubleStick remains flexible to temperatures as low as -57°C making it virtually impossible to thermally shock the seal causing a leak.
DoubleStick Bonds to a wide range of surfaces including EPDM, TPO, most PVC, CSPE/ Hypalon, CPE , SBS, APP modifieds, asphalt BURs, coal tar BURs, tiles, shingle, coated and non-coated aluminum and metal roofs, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry, OSB board, shielding membranes, etc.
Basic Use
DoubleStick tape is a self-sealing adhesive creating a water-tight, conformable seal between two or more irregular surfaces, and/or creates a weather proof, permanent bond between two or more similar or dissimilar surfaces. Use as a lap seal, under the foot of an equipment curb or skylight, or roll it into a bead or ball of MicroSealant to form a gasket, seal a hole or gap as needed.
For info contact: info@eternabond.co.nz
Composition
DoubleStick utilizes EternaBond’s advanced MicroSealant Technology, a 100% solids formulation of synthetic resins, thermoplastics and non-curing rubber (non butyl) with a built in primer, between two silicone release liners.
Technical Data
| Adhesion | 8.64 kilos/in width |
| Application Temperature | 66°C to -29°C ambient |
| Available Widths | Up to 121.9cm as special order |
| Dielectric Strength | Exceeds 12 kV |
| Elongation | >500% |
| Insulation Resistance | 10 to the 6th power megohms |
| Low Temperature Flexibility | 12.7mm radius at -34.4°C |
| Permanence | .001 perms maximum |
| Shelf Life | Up to 5 years |
| Pliability | No cracks in membrane |
| Standard Case Quantity | 30.5 sq. meters per case |
| Standard Roll Sizes | 1.5cm, 2.5cm, 5cm, 7.6cm x 15.2m |
| Temperature Flexibility Range | -57°C - >93°C |
| Total Thickness Standard | 30 mils (0.77MM) or 60mils 1.54mm) |
| Water Vapor Test | (ASTME 96B) .005 grms/24hrs/37.7°C |
| Note:Values are typical performance properties and characteristics based on laboratory testing. This is intended as a guide for comparison purposes and does not constitute a specification or specification range. |
Surface Preparation
Surface must be clean and dry. Moisture, dust, dirt, or other foreign matter should be removed. Remove oil and grease, etc. with EternaClean or a non residue cleaner such as acetone or lacquer thinner. Remove salt and other contaminants.
Application
To apply the DoubleStick, remove one side of the release liner and apply to the surface to be protected or bonded. Rub or roll with pressure using your hand or a steel roller to activate bonding process. Remove the second release liner and apply second surface to tape, apply pressure. DoubleStick also can be used as a putty.
Remove both release liners and roll into a rope. Place over gap and mold to seal opening. This material may be applied to clean dry surfaces from 66°C to -29°C ambient. Treat surface with EternaPrime for installations from 5°C to -29°C ambient.
For more info contact info@eternabond.co.nz |
Back to EternaBond
Download our Limited Warranty (PDF - 21Kb)